Re: [linux-audio-dev] Looking for simple and good multichannel audio soluution.

http://www.behringer.com/ADA8000/index.cfm?lang=ENG
This is cheap and though not the highest quality, still gets the job
done fairly nicely. It would work well with something like the RME
Hammerfall cards.

Or something like this with comp/lim and better dynamic range.
(and which would also support my rent this month :) )
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=7310979716&rd=1&sspagename=STRK%3AMESE%3AIT&rd=1

Cheers,
Shane

On Sat, 2005-03-26 at 20:25, Hans Davidson wrote:
> _______________________________________________________
> Skicka gratis SMS!
> http://www.passagen.se
>
>
>
>
> ______________________________________________________________________
> From: Hans Davidson <harley42@email-addr-hidden>
> To: linux-audio-dev@email-addr-hidden
> Cc: harley42@email-addr-hidden
> Subject: Looking for simple and good multichannel audio soluution.
> Date: Sun, 27 Mar 2005 04:18:02 +0200
>
> Hi all !
>
> I am looking for simple and good multichannel audio solution, of
> course based on a PC and an open source OS.
>
> I have until now managed to output 4 synchronized channels without
> causing need for synchronization of hardware units with each other.
> I have also managed to create sound controlled from the keyboard
> using additive sythesis and with low latancy.
>
> I know that I can use the ".asoundrc" file to make a virtual
> soundcard with for example 4 analog output channels from each card
> (in this case I used CMIPCI based cards intended for 5.1 sound),
> but insertion of about 3 or more sound cards in a single PC may
> cause problems, like a computer that refuses to boot.
> You may also need to replace the Xtal oscilators with an oscilator
> that is common for all the cards.
>
> I have found cards that is expected to work with some applications
> on some operating systems to output multichannel audio in 6 or even
> 8 channels, but it seems like these capabilities are special cases
> that assumes special encoding (not just multiplexing) of the input
> data.
>
> Am I wrong ?
> Are there exceptions ?
> If someone knows about a soundcard, in the "consumer electronics
> segment", with support for maybe 8 (or at least more than 4) analog
> channels from the same amount of INDEPENDENT digital sources
> (through a sinlge multiplexing application program), then PLEASE
> tell me.
>
> It may be possible that the most cost effective way to do what I
> want to do is to use a digital interface (like ADAT, which is
> assumed to work over a TOS-link cable) and connect some 8-channel
> D/A-convertion box or maybe, there is some PCI-based prototype
> card with half-made Linux drivers and an interface that allows
> an appropriate amount of 16-, 20- or 24-bit DAC circuits to
> be easily connected (prefarably through digital oversampling
> filters to simplify the analog parts after the hold cirquits.
>
> An example of what I want to be able to do, is to play back 7
> channels previously stored uncompressed on hard disk and at the
> same time synthezise the last channel from events received over a
> network card or MIDI-IN-connector with low latancy and in the same
> application that is multiplexing the other 7 channels. At the same
> time I may want to record maybe a couple of analog inputs. I think
> that 44.1 kHz sampling rate is quite enough for me both for inputs
> and outputs.
> The hardware should not have too high noise levels, but still
> being cheap enough to buy or build.
> If I fail to observe enough realtime properties in trying this,
> then I can temporarily try using RAM-disk instead of hard disk
> and later redesign with proper use of multithreading or multiple
> processess and priorities.
>
> There seem to be several more possibilities, like using
> several PCs with a 100Mbps or 1Gbps network card and a
> sound card in every box and then using 3 analog outputs
> from every box to feed 3 of the speaker amplifier channels and
> the 4th analog output to output test signals to make it possible
> to meassure how the soundcards are related in time and
> phase with each other. Here, a problems may need to be
> solved, because if playback of prerecorded audio data spans over
> several sound cards (in different boxes), then the data need
> to be resampled (interpolated) for a different sample rate based
> on the feedback.
>
> Is there any obvious good and cheap way for me, or another person
> willing to write some code and/or using a soldering device
> to implement the sound system described above ?
>
> Best regards !
> Hans Davidson
>
>
>
> _______________________________________________________
> Skicka gratis SMS!
> http://www.passagen.se
>
>
>
>
Received on Sun Mar 27 08:15:08 2005