Re: [LAD] RME FIREFACE 400? RME MULTIFACE II?

On Sun, 2011-05-22 at 12:46 +0200, Ralf wrote:
> On Sun, 2011-05-22 at 12:08 +0200, Jörn Nettingsmeier wrote:
> > On 05/22/2011 11:43 AM, Ralf wrote:
> > > Hi :)
> > >
> > > I only watched pictures and read texts but didn't hear one of those RME
> > > devices, anyway, until now I tend to order the RME FIREFACE 400 or RME
> > > MULTIFACE II if they shouldn't cause issues with Linux. The two HDSP be
> > > possible too.
> > >
> > > Any experiences, information?
> >
> > ralf, as usual, your level of disinformation is astonishing.
>
> Hi Jörn,
>
> thank you :).
>
> Disinformation? I didn't have any information, neither right nor wrong
> information, that's why I'm asking.
>
> > the fireface is an ieee1394 device, and the ffado drivers are somewhat
> > experimental. so yes, this would be an "issue with linux". i suggest you
> > check the ffado.org website and look through the ffado mailing list
> > archive to see if the current level of support is sufficient for what
> > you want to do.
> >
> > the multiface ii is a break-out and converter box. it doesn't work on
> > its own. consequently, there are no driver issues associated with its
> > use, other than the firmware upload which the host computer has to take
> > care of when you boot the device.

Oops, my broken English ... there are issues? Googleing for "multiface
ii linux" results with reported issue :S.

> > what you want to look into is the corresponding pci(e) card with the
> > connector that looks like firewire but isn't (proprietary rme protocol).
> > the quality of the converters on the multiface leaves nothing to be desired.
>
> You do write the same as another one does write in a forum :). I tend to
> order a Multiface.
>
> > the 9652 and 9636 cards are digital-only, with two resp. three adat i/o
> > connectors. consequently, their "sound quality" is perfect.
> > you will have to combine them with some external adat ad/da converter.
> >
> > most if not all rme cards come pci and pci express flavours. as you
> > mentioned in a previous posting, the pci prices have dropped a lot, but
> > when you consider one, factor in the cost for mainboards with pci slots
> > - they will become quite rare in mass market in the near future, and
> > then you would have to pay extra to get some "industry"-type product
> > that still has them. for an idea of the extra cost, try shopping for an
> > industry board with ISA slots today (still needed to run legacy process
> > control cards and whatnot).
>
> Yes, my ASUS M2A-VM HDMI motherboard only has 2 PCI slots, occupied by 2
> Terratec EWX 24/96 cards.
> I removed the HDMI thingy and used the PCIe slot for a GeForce 7200GS,
> because 3D doesn't work for the integrated Radeon X1250-based graphics.
>
> Btw. the board has got one PCIe x16 and one PCIe x1 slot.
>
> I could remove the GeForce, 3D isn't important at the moment. Because
> the Multiface is less expensive, I also could order a new motherboard,
> if I should need 3D ... perhaps, I don't know what I need to replace
> too, I randomly picked some mobos ... DDR3 instead of DDR2 seems to be
> no moneywise issue, I guess this is all I would need to change.
>
> So the future is NO PCI, but several PCIe x16 and x1 slots?
>
> > all rme cards i've come across will happily run at 64 frames, and some
> > of the newer ones let you go down to 32 or 16, although i have not tried
> > this yet.
>
> Somebody on a forum wrote that 32 frames are ok for his RME, for a real
> multi-channel productions!
>
> Thank you very much. My impression is that RME cards are the best choice
> for Linux.
>
> Best,
>
> Ralf
>

_______________________________________________
Linux-audio-dev mailing list
Linux-audio-dev@lists.linuxaudio.org
http://lists.linuxaudio.org/listinfo/linux-audio-dev
Received on Sun May 22 16:15:03 2011