Subject: Re: [linux-audio-user] RME Cardbus + multiface
From: Tim Blechmann (TimBlechmann_AT_gmx.net)
Date: Sun Jan 11 2004 - 19:48:46 EET
> Currently with the card inserted what is the output from
> 'lspci -v' ?
> If you can more fully express the symptoms of your problem, then we
> can help solve it. If you have done so before, I don't think I saw
> it....
the hdsp is recognized by the system, the modules load (more or less)
fine, i can upload the firmware ... but when i try to play a sound the
sound sounds distorted ... a sound-file played with aplay seems to have
the right pitch, but takes longer than it should ... it seems that there
are gaps of a few ms where nothing is played ...
the mixer works fine, i can route an input signal to the outputs, but if
a sound application is started (jack,aplay...) the sound starts to get
this distortion i described earlier ... when i change the sample rate
(hdspconf) the pitch of the distortion changes...
the content of lspci -vv is:
00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host
Bridge (rev 04)
Subsystem: Acer Incorporated [ALI]: Unknown device 0019
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at ec000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] #09 [9104]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW+ Rate=x1
00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge
(rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 96
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00003000-00003fff
Memory behind bridge: e8000000-e80fffff
Prefetchable memory behind bridge: f0000000-f7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB PCI Bridge (rev 05)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 00004000-00004fff
Memory behind bridge: e8100000-e81fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 05) (prog-if 80
[Master])
Subsystem: Acer Incorporated [ALI]: Unknown device 0019
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at 1800 [size=16]
00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 05)
(prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI]: Unknown device 0019
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at 1820 [size=32]
00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 05)
Subsystem: Acer Incorporated [ALI]: Unknown device 0019
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1810 [size=16]
00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 05)
(prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI]: Unknown device 0019
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 1840 [size=32]
00:1f.5 Multimedia audio controller: Intel Corp. 82801BA/BAM AC'97 Audio
(rev 05)
Subsystem: Acer Incorporated [ALI]: Unknown device 0019
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 1880 [size=64]
00:1f.6 Modem: Intel Corp. Intel 537 [82801BA/BAM AC'97 Modem] (rev 05)
(prog-if 00 [Generic])
Subsystem: Acer Incorporated [ALI]: Unknown device 0019
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility
M6 LY (prog-if 00 [VGA])
Subsystem: Acer Incorporated [ALI]: Unknown device 0019
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR+ FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at e8000000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW-
Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 CardBus bridge: O2 Micro, Inc. OZ6933 Cardbus Controller (rev
01)
Subsystem: Acer Incorporated [ALI]: Unknown device 0019
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 20000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 20400000-207ff000 (prefetchable)
Memory window 1: 20800000-20bff000
I/O window 0: 00004400-000044ff
I/O window 1: 00004800-000048ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
02:00.1 CardBus bridge: O2 Micro, Inc. OZ6933 Cardbus Controller (rev
01)
Subsystem: Acer Incorporated [ALI]: Unknown device 0019
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 20001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 20c00000-20fff000 (prefetchable)
Memory window 1: 21000000-213ff000
I/O window 0: 00004c00-00004cff
I/O window 1: 00005000-000050ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
02:08.0 Ethernet controller: Intel Corp. 82801BA/BAM/CA/CAM Ethernet
Controller (rev 03)
Subsystem: Acer Incorporated [ALI]: Unknown device 0019
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e8100000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 4000 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
03:00.0 Multimedia audio controller: Xilinx Corporation RME Hammerfall
DSP (rev 0a)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 20800000 (32-bit, non-prefetchable) [size=64K]
dmesg after starting pcmcia, pluging in the cardbus card, running
hdsploader:
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x20f 0x378-0x37f
0x3c0-0x3df 0x4d0-0x4d7
PCI: Enabling device 0000:03:00.0 (0080 -> 0082)
PCI: Setting latency timer of device 0000:03:00.0 to 64
ALSA sound/pci/rme9652/hdsp.c:663: Hammerfall-DSP: no Digiface or
Multiface connected!
ALSA sound/pci/rme9652/hdsp.c:5042: card initialization pending :
waiting for firmware
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0: clocking to 48000
ALSA sound/pci/intel8x0.c:2696: joystick(s) found
ALSA sound/pci/rme9652/hdsp.c:807: wait for FIFO status <= 0 failed
after 30 iterations
ALSA sound/pci/rme9652/hdsp.c:4711: initializing firmware upload
ALSA sound/pci/rme9652/hdsp.c:678: loading firmware
ALSA sound/pci/rme9652/hdsp.c:716: finished firmware loading
i had to run hdsploader 2 times (hdsp.c:807)
the content of /proc/asound/DSP/hdsp:
RME Hammerfall DSP + Multiface (Card #1)
Buffers: capture db000000 playback dac00000
IRQ: 5 Registers bus: 0x20800000 VM: 0xe0917000
Control register: 0x10040de
Control2 register: 0x0
Status register: 0x12000000
Status2 register: 0xffff0703
FIFO status: 0
MIDI1 Output status: 0xffffff00
MIDI1 Input status: 0xffffff00
MIDI2 Output status: 0xffffff00
MIDI2 Input status: 0xffffff00
Buffer Size (Latency): 8192 samples (2 periods of 32768 bytes)
Hardware pointer (frames): 0
Passthru: no
Line out: on
Firmware version: 5
Sample Clock Source: Internal 48 kHz
Preferred Sync Reference: ADAT1
AutoSync Reference: None
AutoSync Frequency: 0
System Clock Mode: Master
System Clock Frequency: 48000
IEC958 input: Coaxial
IEC958 output: Coaxial only
IEC958 quality: Consumer
IEC958 emphasis: off
IEC958 NonAudio: off
IEC958 sample rate: Error flag set
ADAT1: No Lock
SPDIF: No Lock
Word Clock: No Lock
ADAT Sync: No Lock
i checked several configurations in the last 10 days ... several alsa
versions, i even installed kernel 2.6.1-rc3 ... no success
and i installed winxp, which worked fine ... so the device works ...
since both paul davies and thomas charbonnel have not really an idea,
what's the problem i doubt that it's a problem on the alsa side ... my
16bit wlan card works fine on this machine, but it's the only 32bit
cardbus card i ever tried on this machine ...
i'm nearly at a point where i consider selling my (not that old)
notebook (acer aspire 1400) and buying a new one ...
so it would be pretty cool, if you figure out what's the problem with my
system...
Tim mailto:TimBlechmann_AT_gmx.de
ICQ: 96771783
--
The only people for me are the mad ones, the ones who are mad to live,
mad to talk, mad to be saved, desirous of everything at the same time,
the ones who never yawn or say a commonplace thing, but burn, burn,
burn, like fabulous yellow roman candles exploding like spiders across
the stars and in the middle you see the blue centerlight pop and
everybody goes "Awww!"
Jack Kerouac
This archive was generated by hypermail 2b28 : Sun Jan 11 2004 - 18:55:00 EET